SpeedBox 1.0 for BOSCH Smart System - E-Bike Chip Tuning Module

SpeedBox 1.0 for Bosch Smart System

PROPERTIES:

Maximum speed: 50 km/ h

Display shows:
   actual values (only in km/h)
   correct travelled distance (after the countdown process is
   finished)

Activation: WALK function / + - + -

Indication of tuning activation/deactivation: YES (2,5/9,9 km/h)

Compatible with:
   display KIOX 300
   display Intuvia 100
   motors Performance Line - Smart System
   motors Performance Line CX - Smart System
   motors Performance Line CX Race - Smart System

Not compatible with e-bikes that have a magnet attached to a valve (Bosch Rim Magnet)

The tuning for e-bikes with the newest Bosch Gen4 motor and Smart System.

SpeedBox 1.0 enables you to suppress the speed limiter on your e-bike. When in use, the display shows the real speed up to 22.2 km/h. After exceeding this speed your actual speed is indicated on the last two digits of the display.

Example:

- 22.3 corresponds to a speed of 23 km/h

- 23.1 corresponds to a speed of 31 km/h

If you want to see correct speed and all riding data during your ride, we recommend choosing SpeedBox 1.0 B.Tuning for Bosch - you can see the real values in SpeedBox App – right on the display of your phone.

How does SpeedBox 1.0 work?

To activate all the functions of the SpeedBox correctly, it is necessary to enter the menu after the first switching on of the e-bike after the tuning installation and switch to the circumference of the wheel of your e-bike.

You will activate the SpeedBox 1.0 tuning directly on your e-bike’s control unit by activating the WALK assist function shortly (holding down the “-” button). Your e-bike display will show a value of 9,9 km/h (6,2 mph) and from now on you will be able to ride at unlimited speed.

To deactivate the tuning, activate the WALK assist function shortly again (by holding down the “-” button). Your e-bike display will show a value of 2,5 km/h (1,6 mph) and the speed limit will be reset to 25 km/h. Your e-bike will then work the same as before the tuning installation.

SpeedBox was also designed for e-bikes that do not have the WALK assist function enabled, or activated. In this case, you can activate/deactivate tuning by switching between two assistance modes twice, i.e. by pressing the + - + - buttons.

The "countdown" process will continue concealed during charging, therefore, if you charge your e-bike with a connected battery, you can ignore the following instructions. If you need to remove the battery from your e-bike in order to charge it, you need to wait for the SpeedBox to carry out the "countdown" process after the ride. When you stop your e-bike, the ongoing "countdown" process will be indicated by the increasing riding time. Once the "countdown" process is completed, the riding time stops and the e-bike display shows the correct distance travelled. The countdown process can be interrupted by turning off the e-bike or by setting off, so it does not restrict the use of your e-bike in any way. However, you still need to have the countdown process run regularly to prevent tuning detection.

Assembly

We use original connectors for the production of SpeedBox products ensuring that the installation process is very simple and the SpeedBox is connected properly. We have also prepared detailed instructions and videos to make installation easy for you. Disassembly of the SpeedBox is just as easy. If you have any troubles with installation or disassembly, do not hesitate to contact us.

If you are planning to install SpeedBox on a brand-new bike, make sure you ride it for at least 1 km before the tuning is activated.

Important:

Connect the male - female connectors in the direction of the lock. Do not rotate the connectors during connection!

Warning

Please note that the operation of this type of modified electric bikes on public roads may be against the law in some countries. The manufacturer takes no responsibility for damages resulting from the use SpeedBox products. Electric bikes equipped with SpeedBox products are not allowed to be used on public roads, cycling paths and public places. Electric bikes equipped with SpeedBox products can be used exclusively on private property and entirely at one’s own risk. The use of SpeedBox may void the warranty of your ebike.

We strongly recommend using other safety features and protective gear to prevent injuries.

In case of updating the software of your e-bike, we recommend the following procedure:

1) Uninstall SpeedBox from the e-bike

2) Update the software

3) Reinstall SpeedBox

Scope of delivery:

• SpeedBox 1.0 for Bosch Smart System